Class: Tinkerforge::BrickletRotaryPotiV2

Inherits:
Device
  • Object
show all
Defined in:
lib/tinkerforge/bricklet_rotary_poti_v2.rb

Overview

300° rotary potentiometer

Constant Summary collapse

DEVICE_IDENTIFIER =

:nodoc:

2140
DEVICE_DISPLAY_NAME =

:nodoc:

'Rotary Poti Bricklet 2.0'
CALLBACK_POSITION =

This callback is triggered periodically according to the configuration set by BrickletRotaryPotiV2#set_position_callback_configuration.

The parameter is the same as BrickletRotaryPotiV2#get_position.

4
FUNCTION_GET_POSITION =

:nodoc:

1
FUNCTION_SET_POSITION_CALLBACK_CONFIGURATION =

:nodoc:

2
FUNCTION_GET_POSITION_CALLBACK_CONFIGURATION =

:nodoc:

3
FUNCTION_GET_SPITFP_ERROR_COUNT =

:nodoc:

234
FUNCTION_SET_BOOTLOADER_MODE =

:nodoc:

235
FUNCTION_GET_BOOTLOADER_MODE =

:nodoc:

236
FUNCTION_SET_WRITE_FIRMWARE_POINTER =

:nodoc:

237
FUNCTION_WRITE_FIRMWARE =

:nodoc:

238
FUNCTION_SET_STATUS_LED_CONFIG =

:nodoc:

239
FUNCTION_GET_STATUS_LED_CONFIG =

:nodoc:

240
FUNCTION_GET_CHIP_TEMPERATURE =

:nodoc:

242
FUNCTION_RESET =

:nodoc:

243
FUNCTION_WRITE_UID =

:nodoc:

248
FUNCTION_READ_UID =

:nodoc:

249
FUNCTION_GET_IDENTITY =

:nodoc:

255
THRESHOLD_OPTION_OFF =

:nodoc:

'x'
THRESHOLD_OPTION_OUTSIDE =

:nodoc:

'o'
THRESHOLD_OPTION_INSIDE =

:nodoc:

'i'
THRESHOLD_OPTION_SMALLER =

:nodoc:

'<'
THRESHOLD_OPTION_GREATER =

:nodoc:

'>'
BOOTLOADER_MODE_BOOTLOADER =

:nodoc:

0
BOOTLOADER_MODE_FIRMWARE =

:nodoc:

1
BOOTLOADER_MODE_BOOTLOADER_WAIT_FOR_REBOOT =

:nodoc:

2
BOOTLOADER_MODE_FIRMWARE_WAIT_FOR_REBOOT =

:nodoc:

3
BOOTLOADER_MODE_FIRMWARE_WAIT_FOR_ERASE_AND_REBOOT =

:nodoc:

4
BOOTLOADER_STATUS_OK =

:nodoc:

0
BOOTLOADER_STATUS_INVALID_MODE =

:nodoc:

1
BOOTLOADER_STATUS_NO_CHANGE =

:nodoc:

2
BOOTLOADER_STATUS_ENTRY_FUNCTION_NOT_PRESENT =

:nodoc:

3
BOOTLOADER_STATUS_DEVICE_IDENTIFIER_INCORRECT =

:nodoc:

4
BOOTLOADER_STATUS_CRC_MISMATCH =

:nodoc:

5
STATUS_LED_CONFIG_OFF =

:nodoc:

0
STATUS_LED_CONFIG_ON =

:nodoc:

1
STATUS_LED_CONFIG_SHOW_HEARTBEAT =

:nodoc:

2
STATUS_LED_CONFIG_SHOW_STATUS =

:nodoc:

3

Constants inherited from Device

Device::DEVICE_IDENTIFIER_CHECK_MATCH, Device::DEVICE_IDENTIFIER_CHECK_MISMATCH, Device::DEVICE_IDENTIFIER_CHECK_PENDING, Device::RESPONSE_EXPECTED_ALWAYS_TRUE, Device::RESPONSE_EXPECTED_FALSE, Device::RESPONSE_EXPECTED_INVALID_FUNCTION_ID, Device::RESPONSE_EXPECTED_TRUE

Instance Attribute Summary

Attributes inherited from Device

#callback_formats, #expected_response_function_id, #expected_response_sequence_number, #high_level_callbacks, #registered_callbacks, #replaced, #uid

Instance Method Summary collapse

Methods inherited from Device

#check_validity, #dequeue_response, #enqueue_response, #get_api_version, #get_response_expected, #send_request, #set_response_expected, #set_response_expected_all

Constructor Details

#initialize(uid, ipcon) ⇒ BrickletRotaryPotiV2

Creates an object with the unique device ID uid and adds it to the IP Connection ipcon.



65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 65

def initialize(uid, ipcon)
  super uid, ipcon, DEVICE_IDENTIFIER, DEVICE_DISPLAY_NAME

  @api_version = [2, 0, 0]

  @response_expected[FUNCTION_GET_POSITION] = RESPONSE_EXPECTED_ALWAYS_TRUE
  @response_expected[FUNCTION_SET_POSITION_CALLBACK_CONFIGURATION] = RESPONSE_EXPECTED_TRUE
  @response_expected[FUNCTION_GET_POSITION_CALLBACK_CONFIGURATION] = RESPONSE_EXPECTED_ALWAYS_TRUE
  @response_expected[FUNCTION_GET_SPITFP_ERROR_COUNT] = RESPONSE_EXPECTED_ALWAYS_TRUE
  @response_expected[FUNCTION_SET_BOOTLOADER_MODE] = RESPONSE_EXPECTED_ALWAYS_TRUE
  @response_expected[FUNCTION_GET_BOOTLOADER_MODE] = RESPONSE_EXPECTED_ALWAYS_TRUE
  @response_expected[FUNCTION_SET_WRITE_FIRMWARE_POINTER] = RESPONSE_EXPECTED_FALSE
  @response_expected[FUNCTION_WRITE_FIRMWARE] = RESPONSE_EXPECTED_ALWAYS_TRUE
  @response_expected[FUNCTION_SET_STATUS_LED_CONFIG] = RESPONSE_EXPECTED_FALSE
  @response_expected[FUNCTION_GET_STATUS_LED_CONFIG] = RESPONSE_EXPECTED_ALWAYS_TRUE
  @response_expected[FUNCTION_GET_CHIP_TEMPERATURE] = RESPONSE_EXPECTED_ALWAYS_TRUE
  @response_expected[FUNCTION_RESET] = RESPONSE_EXPECTED_FALSE
  @response_expected[FUNCTION_WRITE_UID] = RESPONSE_EXPECTED_FALSE
  @response_expected[FUNCTION_READ_UID] = RESPONSE_EXPECTED_ALWAYS_TRUE
  @response_expected[FUNCTION_GET_IDENTITY] = RESPONSE_EXPECTED_ALWAYS_TRUE

  @callback_formats[CALLBACK_POSITION] = [10, 's']

  @ipcon.add_device self
end

Instance Method Details

#get_bootloader_mode ⇒ Object

Returns the current bootloader mode, see BrickletRotaryPotiV2#set_bootloader_mode.



175
176
177
178
179
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 175

def get_bootloader_mode
  check_validity

  send_request FUNCTION_GET_BOOTLOADER_MODE, [], '', 9, 'C'
end

#get_chip_temperature ⇒ Object

Returns the temperature as measured inside the microcontroller. The value returned is not the ambient temperature!

The temperature is only proportional to the real temperature and it has bad accuracy. Practically it is only useful as an indicator for temperature changes.



233
234
235
236
237
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 233

def get_chip_temperature
  check_validity

  send_request FUNCTION_GET_CHIP_TEMPERATURE, [], '', 10, 's'
end

#get_identity ⇒ Object

Returns the UID, the UID where the Bricklet is connected to, the position, the hardware and firmware version as well as the device identifier.

The position can be ‘a’, ‘b’, ‘c’, ‘d’, ‘e’, ‘f’, ‘g’ or ‘h’ (Bricklet Port). A Bricklet connected to an :ref:‘Isolator Bricklet <isolator_bricklet>` is always at position ’z’.

The device identifier numbers can be found :ref:‘here <device_identifier>`. |device_identifier_constant|



280
281
282
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 280

def get_identity
  send_request FUNCTION_GET_IDENTITY, [], '', 33, 'Z8 Z8 k C3 C3 S'
end

#get_position ⇒ Object

Returns the position of the rotary potentiometer. The value is between -150° (turned left) and 150° (turned right).

If you want to get the value periodically, it is recommended to use the CALLBACK_POSITION callback. You can set the callback configuration with BrickletRotaryPotiV2#set_position_callback_configuration.



98
99
100
101
102
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 98

def get_position
  check_validity

  send_request FUNCTION_GET_POSITION, [], '', 10, 's'
end

#get_position_callback_configuration ⇒ Object

Returns the callback configuration as set by BrickletRotaryPotiV2#set_position_callback_configuration.



136
137
138
139
140
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 136

def get_position_callback_configuration
  check_validity

  send_request FUNCTION_GET_POSITION_CALLBACK_CONFIGURATION, [], '', 18, 'L ? k s s'
end

#get_spitfp_error_count ⇒ Object

Returns the error count for the communication between Brick and Bricklet.

The errors are divided into

  • ACK checksum errors,

  • message checksum errors,

  • framing errors and

  • overflow errors.

The errors counts are for errors that occur on the Bricklet side. All Bricks have a similar function that returns the errors on the Brick side.



153
154
155
156
157
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 153

def get_spitfp_error_count
  check_validity

  send_request FUNCTION_GET_SPITFP_ERROR_COUNT, [], '', 24, 'L L L L'
end

#get_status_led_config ⇒ Object

Returns the configuration as set by BrickletRotaryPotiV2#set_status_led_config



221
222
223
224
225
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 221

def get_status_led_config
  check_validity

  send_request FUNCTION_GET_STATUS_LED_CONFIG, [], '', 9, 'C'
end

#read_uid ⇒ Object

Returns the current UID as an integer. Encode as Base58 to get the usual string version.



264
265
266
267
268
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 264

def read_uid
  check_validity

  send_request FUNCTION_READ_UID, [], '', 12, 'L'
end

#register_callback(id, &block) ⇒ Object

Registers a callback with ID id to the block block.



285
286
287
288
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 285

def register_callback(id, &block)
  callback = block
  @registered_callbacks[id] = callback
end

#reset ⇒ Object

Calling this function will reset the Bricklet. All configurations will be lost.

After a reset you have to create new device objects, calling functions on the existing ones will result in undefined behavior!



245
246
247
248
249
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 245

def reset
  check_validity

  send_request FUNCTION_RESET, [], '', 8, ''
end

#set_bootloader_mode(mode) ⇒ Object

Sets the bootloader mode and returns the status after the requested mode change was instigated.

You can change from bootloader mode to firmware mode and vice versa. A change from bootloader mode to firmware mode will only take place if the entry function, device identifier and CRC are present and correct.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.



168
169
170
171
172
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 168

def set_bootloader_mode(mode)
  check_validity

  send_request FUNCTION_SET_BOOTLOADER_MODE, [mode], 'C', 9, 'C'
end

#set_position_callback_configuration(period, value_has_to_change, option, min, max) ⇒ Object

The period is the period with which the CALLBACK_POSITION callback is triggered periodically. A value of 0 turns the callback off.

If the ‘value has to change`-parameter is set to true, the callback is only triggered after the value has changed. If the value didn’t change within the period, the callback is triggered immediately on change.

If it is set to false, the callback is continuously triggered with the period, independent of the value.

It is furthermore possible to constrain the callback with thresholds.

The ‘option`-parameter together with min/max sets a threshold for the CALLBACK_POSITION callback.

The following options are possible:

"Option", "Description"

"'x'",    "Threshold is turned off"
"'o'",    "Threshold is triggered when the value is *outside* the min and max values"
"'i'",    "Threshold is triggered when the value is *inside* or equal to the min and max values"
"'<'",    "Threshold is triggered when the value is smaller than the min value (max is ignored)"
"'>'",    "Threshold is triggered when the value is greater than the min value (max is ignored)"

If the option is set to ‘x’ (threshold turned off) the callback is triggered with the fixed period.



129
130
131
132
133
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 129

def set_position_callback_configuration(period, value_has_to_change, option, min, max)
  check_validity

  send_request FUNCTION_SET_POSITION_CALLBACK_CONFIGURATION, [period, value_has_to_change, option, min, max], 'L ? k s s', 8, ''
end

#set_status_led_config(config) ⇒ Object

Sets the status LED configuration. By default the LED shows communication traffic between Brick and Bricklet, it flickers once for every 10 received data packets.

You can also turn the LED permanently on/off or show a heartbeat.

If the Bricklet is in bootloader mode, the LED is will show heartbeat by default.



214
215
216
217
218
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 214

def set_status_led_config(config)
  check_validity

  send_request FUNCTION_SET_STATUS_LED_CONFIG, [config], 'C', 8, ''
end

#set_write_firmware_pointer(pointer) ⇒ Object

Sets the firmware pointer for BrickletRotaryPotiV2#write_firmware. The pointer has to be increased by chunks of size 64. The data is written to flash every 4 chunks (which equals to one page of size 256).

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.



187
188
189
190
191
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 187

def set_write_firmware_pointer(pointer)
  check_validity

  send_request FUNCTION_SET_WRITE_FIRMWARE_POINTER, [pointer], 'L', 8, ''
end

#write_firmware(data) ⇒ Object

Writes 64 Bytes of firmware at the position as written by BrickletRotaryPotiV2#set_write_firmware_pointer before. The firmware is written to flash every 4 chunks.

You can only write firmware in bootloader mode.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.



201
202
203
204
205
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 201

def write_firmware(data)
  check_validity

  send_request FUNCTION_WRITE_FIRMWARE, [data], 'C64', 9, 'C'
end

#write_uid(uid) ⇒ Object

Writes a new UID into flash. If you want to set a new UID you have to decode the Base58 encoded UID string into an integer first.

We recommend that you use Brick Viewer to change the UID.



256
257
258
259
260
 
# File 'lib/tinkerforge/bricklet_rotary_poti_v2.rb', line 256

def write_uid(uid)
  check_validity

  send_request FUNCTION_WRITE_UID, [uid], 'L', 8, ''
end